TotalCaptureResult

Color correction processing must not slow down capture rate relative to sensor raw output.

Use the android.colorCorrection.transform matrix and android.colorCorrection.gains to do color conversion.

The camera device will adjust exposure duration to avoid banding problems with 60Hz illumination sources.

The camera device will not adjust exposure duration to avoid banding problems.

The camera device's autoexposure routine is active, with no flash control.

Like ON, except that the camera device also controls the camera's flash unit, firing it in low-light conditions.

The trigger is idle.

AE has a good set of control values for the current scene.

AE is off or recently reset.

AE has been asked to do a precapture sequence and is currently executing it.

Basic automatic focus mode.

In this mode, the AF algorithm modifies the lens position continually to attempt to provide a constantly-in-focus image stream.

Close-up focusing mode.

AF is performing an AF scan because it was triggered by AF trigger.

AF is off or has not yet tried to scan/been asked to scan.

AF currently believes it is in focus, but may restart scanning at any time.

AF finished a passive scan without finding focus, and may restart scanning at any time.

The trigger is idle.

The camera device's auto-white balance routine is active.

The camera device's auto-white balance routine is disabled; the camera device uses daylight light as the assumed scene illumination for white balance.

The camera device's auto-white balance routine is disabled; the camera device uses incandescent light as the assumed scene illumination for white balance.

The camera device's auto-white balance routine is disabled; the camera device uses shade light as the assumed scene illumination for white balance.

The camera device's auto-white balance routine is disabled; the camera device uses warm fluorescent light as the assumed scene illumination for white balance.

AWB is not in auto mode, or has not yet started metering.

AWB doesn't yet have a good set of control values for the current scene.

This request is for manual capture use case where the applications want to directly control the capture parameters.

This request is for a still capture-type use case.

This request is for a video snapshot (still image while recording video) use case.

An "aqua" effect where a blue hue is added to the image.

A "monocolor" effect where the image is mapped into a single color.

No color effect will be applied.

A "sepia" effect where the image is mapped into warm gray, red, and brown tones.

A "whiteboard" effect where the image is typically displayed as regions of white, with black or grey details.

Full application control of pipeline.

Use a specific scene mode.

Optimized for accurately capturing a photo of barcode for use by camera applications that wish to read the barcode value.

Optimized for dim settings where the main light source is a flame.

If face detection support exists, use face detection data for auto-focus, auto-white balance, and auto-exposure routines.

Optimized for photos of distant macroscopic objects.

Optimized for still photos of people in low-light settings.

Optimized for still photos of people.

Optimized for photos of quickly moving people.

Optimized for scenes of the setting sun.

Video stabilization is disabled.

Apply edge enhancement at a quality level that does not slow down frame rate relative to sensor output

No edge enhancement is applied.

If the flash is available and charged, fire flash for this capture.

Flash is charging and cannot be fired.

Flash partially illuminated this frame.

No flash on camera.

High-quality hot pixel correction is applied, at a cost of reducing frame rate relative to sensor raw output.

This camera device is capable of supporting advanced imaging applications.

The camera device faces the opposite direction as the device's screen.

The lens focus distance is measured in diopters.

The lens focus distance is not accurate, and the units used for android.lens.focusDistance do not correspond to any physical units.

Optical stabilization is enabled.

The lens parameters (android.lens.focalLength, android.lens.focusDistance, android.lens.filterDensity and android.lens.aperture) are not changing.

High-quality noise reduction is applied, at the cost of reducing frame rate relative to sensor output.

The camera device supports outputting RAW buffers that can be saved offline into a DNG format.

The camera device can be manually controlled (3A algorithms such as auto-exposure, and auto-focus can be bypassed).

The camera device supports arbitrarily chosen crop regions.

Sensor is not Bayer; output has 3 16-bit values for each pixel, instead of just 1 16-bit value per pixel.

N 4600 - 5400K

WW 3200 - 3700K

The test pattern is similar to COLOR_BARS, except that each bar should start at its specified color at the top, and fade to gray at the bottom.

No test pattern mode is used, and the camera device returns captures from the image sensor.

Each pixel in [R, G_even, G_odd, B] is replaced by its respective color channel provided in android.sensor.testPatternData.

Apply high-quality lens shading correction, at the cost of reduced frame rate.

Return all face metadata.

Return face rectangle and confidence values only.

Include a lens shading map in the capture result.

The camera device detects illumination flickering at 60Hz in the current scene.

Every frame has the requests immediately applied.

Use the tone mapping curve specified in the android.tonemap.curve* entries.

High-quality gamma mapping and color enhancement will be applied, at the cost of reduced frame rate compared to raw sensor output.

Whether black-level compensation is locked to its current values, or is free to vary.

The mode control selects how the image data is converted from the sensor's native color into linear sRGB color.

The desired setting for the camera device's auto-exposure algorithm's antibanding compensation.

Whether auto-exposure (AE) is currently locked to its latest calculated values.

Whether the camera device will trigger a precapture metering sequence when it processes this request.

Current state of the auto-exposure (AE) algorithm.

Whether auto-focus (AF) is currently enabled, and what mode it is set to.

Current state of auto-focus (AF) algorithm.

Whether auto-white balance (AWB) is currently locked to its latest calculated values.

List of areas to use for illuminant estimation.

Information to the camera device 3A (auto-exposure, auto-focus, auto-white balance) routines about the purpose of this capture, to help the camera device to decide optimal 3A strategy.

Overall mode of 3A control routines.

Whether video stabilization is active.

The desired mode for for the camera device's flash control.

Set operational mode for hot pixel correction.

Orientation of JPEG image to write

Compression quality of JPEG thumbnail.

The ratio of lens focal length to the effective aperture diameter.

The current lens focal length; used for optical zoom.

The range of scene distances that are in sharp focus (depth of field).

Current lens status.

A frame counter set by the framework.

The region of the sensor to read out for this capture.

Duration from start of frame exposure to start of next frame exposure.

The estimated camera neutral color in the native sensor colorspace at the time of capture.

A pixel [R, G_even, G_odd, B] that supplies the test pattern when android.sensor.testPatternMode is SOLID_COLOR.

Time at start of exposure of first row of the image sensor, in nanoseconds.

List of the faces detected through camera face detection in this result.

List of (x, y) coordinates of hot/defective pixels on the sensor.

The shading map is a low-resolution floating-point map that lists the coefficients used to correct for vignetting, for each Bayer color channel.

The camera device estimated scene illumination lighting frequency.

High-level global contrast/gamma/tonemapping control.